Mapúa UniversityMuralla St., Intramuros, ManilaSchool of Mechanical and Manufacturing EngineeringCommon hand tools in shop practiceExercise 1 RAPANAN, Denzel A.November 11, 20182018162103 November 2018Engr.
Rj Lawrence TiuInstructorTOOLS DESCRIPTION / SAFETY right8255It is a like just a compass with inward or outward facing points. It measure the width, raduis and outside diameters of object. Avoid using your caliper to measure moving parts of machinery, as this can affect the shape of its measuring faces, and therefore the accuracy of your measurements.The pliers intended for the cutting of wirePliers should not be used for cutting heavy wire unless it is specifically made for this purpose.This is for both cutting and holding pliers and used by artisans, jewellery designers, electricians, network engineers and other tradesmen to bend, re-position and snip wire.
Do not bend stiff wire with light pliers. Using the tips to bend too large a wire can damage long-nose pliers.It is a bendable measuring device, it can use to measure distance.Do not play this tool because it can cause you cuts and injuries. 00It is a like just a compass with inward or outward facing points. It measure the width, raduis and outside diameters of object. Avoid using your caliper to measure moving parts of machinery, as this can affect the shape of its measuring faces, and therefore the accuracy of your measurements.The pliers intended for the cutting of wirePliers should not be used for cutting heavy wire unless it is specifically made for this purpose.
This is for both cutting and holding pliers and used by artisans, jewellery designers, electricians, network engineers and other tradesmen to bend, re-position and snip wire.Do not bend stiff wire with light pliers. Using the tips to bend too large a wire can damage long-nose pliers.
It is a bendable measuring device, it can use to measure distance.Do not play this tool because it can cause you cuts and injuries. 1.) Outside Caliper 2.) Side cutter plier3.) Long nose plier4.) Measuring tape right15902 A tool device with a design and shaped cutting edge of blade on its end.
It is for carving or cutting a hard material such as wood, stone, or metal.Never hold a workpiece with one hand while chiseling with the other. Secure it with a clamp or bench vice.Also know as plumb level is a straight bar (aluminum or wood) with a spirit level embedded on center and both sides.An device designed to indicate whether a surface is horizontal (level) or vertical (plumb). Make sure to guard the spirit level to avoid breaking.It is a multi-use measuring device primarily used for ensuring the integrity of a 90° angle, measuring a 45° angle, measuring the center of a circular object, find depth, and simple distance measurements.
Do not bang the blade on a table as this will damage the combination square and also it will affect you and the people around you.The steel square is often called the carpenter’s square or framing square.It is used for measuring boards, testing corners, and setting the bevel of boards and tools to various angles.Do not drop the blade on a table as this will damage the steel square and it will also affect you and the person beside you.00 A tool device with a design and shaped cutting edge of blade on its end.It is for carving or cutting a hard material such as wood, stone, or metal.Never hold a workpiece with one hand while chiseling with the other.
Secure it with a clamp or bench vice.Also know as plumb level is a straight bar (aluminum or wood) with a spirit level embedded on center and both sides.An device designed to indicate whether a surface is horizontal (level) or vertical (plumb). Make sure to guard the spirit level to avoid breaking.It is a multi-use measuring device primarily used for ensuring the integrity of a 90° angle, measuring a 45° angle, measuring the center of a circular object, find depth, and simple distance measurements.Do not bang the blade on a table as this will damage the combination square and also it will affect you and the people around you.The steel square is often called the carpenter’s square or framing square.
It is used for measuring boards, testing corners, and setting the bevel of boards and tools to various angles.Do not drop the blade on a table as this will damage the steel square and it will also affect you and the person beside you.5.
) Wood Chisel 6.) Carpenter Level7.) Combination square8.) Steel Square337185015875It is a wood-working or a metalworking tool used for marking and measuring a piece of wood specifically use for measuring the accuracy of a right angle (90 degrees);Do not bang the blade on a table as this will damage the try square and it will affect you and the people around you.This a essentially speciality planes. Planes are tools used to shape wood by smoothing and removing small slithers at a time. A hand tool used in woodworking to shave curved pieces of wood down to the required size.
hand plane.Avoid grabbing the spokeshave tightly; instead, hold it lightly using the thumb and forefinger of each hand.It is a type of bow saw used to cut intricate external shapes and interior cut-outs in woodworking or carpentry.
It is used to cut moldings to create coped rather than miter joints.For safely use the coping saw, firmly hold the material in a vise.A crosscut saw is a handy tool for cutting lumber, making furniture, and for other wood-cutting tasks. It is a specialized handsaw for manually cutting wood across the grain.Always be aware that the teeth of a crosscut saw are sharp and pointed. Placing them point-down on an object or a body part will cut it.00It is a wood-working or a metalworking tool used for marking and measuring a piece of wood specifically use for measuring the accuracy of a right angle (90 degrees);Do not bang the blade on a table as this will damage the try square and it will affect you and the people around you.
This a essentially speciality planes. Planes are tools used to shape wood by smoothing and removing small slithers at a time. A hand tool used in woodworking to shave curved pieces of wood down to the required size. hand plane.Avoid grabbing the spokeshave tightly; instead, hold it lightly using the thumb and forefinger of each hand.It is a type of bow saw used to cut intricate external shapes and interior cut-outs in woodworking or carpentry.
It is used to cut moldings to create coped rather than miter joints.For safely use the coping saw, firmly hold the material in a vise.A crosscut saw is a handy tool for cutting lumber, making furniture, and for other wood-cutting tasks. It is a specialized handsaw for manually cutting wood across the grain.Always be aware that the teeth of a crosscut saw are sharp and pointed. Placing them point-down on an object or a body part will cut it.
9.) Try square 10.) Spokeshave11.) Coping saw 12.) Crosscut saw 337185015875Backsaws are normally used in woodworking for precise work, such as cutting dovetails, or tenons in cabinetry and joinery.
Place the saw’s central teeth on the line and push the saw to start the cut. Continue by carefully guiding the teeth over the line, steadying the blade as needed with your other hand.It is a instrument that is primarily used for pounding nails into, or extracting nails from, some other object. Generally, a claw hammer is associated with woodworking but is not limited to use with wood products.
Strike a hammer blow squarely with the striking face parallel to the surface being struck. Always avoid glancing blows and over and under strikes.A type of bench plane used in woodworking and for the finest finishing work on the wood surface.When planing small pieces, hold the plane firmly and move the workpiece across the blade-not the other way around. If possible, anchor the plane against your body for stability.
a tool with a large, flat, often metal head, attached to a lever (or handle).To apply more force than other hammers of similar size.Before operating a sledgehammer, make sure there are obstructions on the floor that you might trip on. This can lead to serious injury.
Also use safety goggles and gloves00Backsaws are normally used in woodworking for precise work, such as cutting dovetails, or tenons in cabinetry and joinery.Place the saw’s central teeth on the line and push the saw to start the cut. Continue by carefully guiding the teeth over the line, steadying the blade as needed with your other hand.It is a instrument that is primarily used for pounding nails into, or extracting nails from, some other object. Generally, a claw hammer is associated with woodworking but is not limited to use with wood products.
Strike a hammer blow squarely with the striking face parallel to the surface being struck. Always avoid glancing blows and over and under strikes.A type of bench plane used in woodworking and for the finest finishing work on the wood surface.When planing small pieces, hold the plane firmly and move the workpiece across the blade-not the other way around. If possible, anchor the plane against your body for stability.a tool with a large, flat, often metal head, attached to a lever (or handle).To apply more force than other hammers of similar size.
Before operating a sledgehammer, make sure there are obstructions on the floor that you might trip on. This can lead to serious injury. Also use safety goggles and gloves13.) Back saw 14.) Claw hammer 15.) Smooth plane 16.
) Sledge hammer 337185015875It is a pair of clippers for cutting sheet metal. Used to cut sheet metal.Always wear safety goggles when using snips. Be careful of the sharp edges of these tools. Wear safety gloves when working with snips especially when handling the edges of the material you are cutting.Used for drilling device and the rotation of the blade causes the material to move out of the hole being drilled.Always wear safety goggles to protect your eyes, gloves to protect your hands, and wear other appropriate safety items for protection.
The purpose of the gauge is to scribe a line parallel to a reference edge or surface.When a cutting gauge is not in use, the fence should be brought, so it is against the knife. This will help protect the knife and keep it sharper for longer.Also used for drilling machine and used to remove material to create holes, almost always of circular cross-section.Be sure drill bits are set straight in the jaws.
Hold up the drill and turn it on for a moment. The bit should run without any wobble.00It is a pair of clippers for cutting sheet metal. Used to cut sheet metal.
Always wear safety goggles when using snips. Be careful of the sharp edges of these tools. Wear safety gloves when working with snips especially when handling the edges of the material you are cutting.Used for drilling device and the rotation of the blade causes the material to move out of the hole being drilled.Always wear safety goggles to protect your eyes, gloves to protect your hands, and wear other appropriate safety items for protection.The purpose of the gauge is to scribe a line parallel to a reference edge or surface.
When a cutting gauge is not in use, the fence should be brought, so it is against the knife. This will help protect the knife and keep it sharper for longer.Also used for drilling machine and used to remove material to create holes, almost always of circular cross-section.
Be sure drill bits are set straight in the jaws. Hold up the drill and turn it on for a moment. The bit should run without any wobble.17.) Tin Snip 18.) Auger bit19.
) Marking gauge20.) Drill bit 337185015875This instrument is made of heavy-duty cast iron with a machined steel screw for optimal durability. It is used to hold together two workpieces.
Never use a clamp with a bend frame or spindle. Clamps are to be hand torqued. Never use pipes, hammers or pliers to tighten down.It is small portable drilling machine resembling a breast drill but designed to be held and operated by hand.Examine your drill to make sure that it is clean. If the drill is dirty or rusty, tag it and return it to supply for maintenance. Make sure the drill speed is proper for the job.A tool used for creating semicircular grooves, finishing and deburring concave surfaces.
There is safety ring attached the file to prevent from falling. Handles are glued to the file to prevent the handles from separating.An instrument used to shape and smooth wood, plastic or metal by filing.
The safety for this is do not use a file as a pry bar, hammer, screwdriver or chisel. When using a file or a rasp, grasp the handle in one hand and the toe of the file in the other.00This instrument is made of heavy-duty cast iron with a machined steel screw for optimal durability. It is used to hold together two workpieces.
Never use a clamp with a bend frame or spindle. Clamps are to be hand torqued. Never use pipes, hammers or pliers to tighten down.It is small portable drilling machine resembling a breast drill but designed to be held and operated by hand.Examine your drill to make sure that it is clean. If the drill is dirty or rusty, tag it and return it to supply for maintenance. Make sure the drill speed is proper for the job.A tool used for creating semicircular grooves, finishing and deburring concave surfaces.
There is safety ring attached the file to prevent from falling. Handles are glued to the file to prevent the handles from separating.An instrument used to shape and smooth wood, plastic or metal by filing.The safety for this is do not use a file as a pry bar, hammer, screwdriver or chisel.
When using a file or a rasp, grasp the handle in one hand and the toe of the file in the other.21.) C- clamp22.) Hand drill 23.) Round file 24.
) Square file337185015875This device has two flat surfaces and used for clearing wood or metal.Handle it with care when using and hold the handle tightly to avoid injuries.A instrument device with a conical point for making an indentation in an object, to allow a drill to make a hole at the same spot without slipping that used to mark the center of a point.Wear safety glasses or goggles, or a face shield.
Use a screen or shield to protect fellow workers from flying debris objects.A sharp metal object that used for joining objects such as wood.Do not used rusty nails and be safe when hammering.A tool for boding objects. An adhesiveAs much as possible, wear gloves and always put the lid close to avoid the clogging.
00This device has two flat surfaces and used for clearing wood or metal.Handle it with care when using and hold the handle tightly to avoid injuries.A instrument device with a conical point for making an indentation in an object, to allow a drill to make a hole at the same spot without slipping that used to mark the center of a point.Wear safety glasses or goggles, or a face shield.
Use a screen or shield to protect fellow workers from flying debris objects.A sharp metal object that used for joining objects such as wood.Do not used rusty nails and be safe when hammering.A tool for boding objects. An adhesiveAs much as possible, wear gloves and always put the lid close to avoid the clogging.
25.) Flat file26.) Center punch 27.) Nail 28.) Wood Glue 29.
) Inside caliper 3371850-170180The same as outside caliper, it is used just like a compass to measure radius and diameter. Avoid using your caliper to measure moving parts of machinery, as this can affect the shape of its measuring faces, and therefore the accuracy of your measurements.A instrument with a long flat sharp edge with handle and used for creating different design when carving wood or stone.It is always said that when sculpting something the person needed to have PPE just like mask, safety glass for safety purposes.
00The same as outside caliper, it is used just like a compass to measure radius and diameter. Avoid using your caliper to measure moving parts of machinery, as this can affect the shape of its measuring faces, and therefore the accuracy of your measurements.A instrument with a long flat sharp edge with handle and used for creating different design when carving wood or stone.It is always said that when sculpting something the person needed to have PPE just like mask, safety glass for safety purposes.30.) Chisel
